Walchem WebMaster Manual de instrucciones Pagina 6
- Pagina / 180
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
2
2.2 Electrical
Inputs
Input power 100 – 120/220-240 VAC ±10%, 12A, 50/60 Hz
Fuse 1.6A, 5 x 20mm
Input signals
State-Type Digital Inputs
Electrical: Non-isolated 5 VDC with 301K ohm pull-up
Typical response time: <10 seconds
Devices supported: Any isolated dry contact (i.e. relay, reed switch)
Types: Interlock, Level switch, Generic input
Low Speed Counter-Type
Digial Inputs
Electrical: Non-isolated 5 VDC with 301K ohm pull-up, 0-10 Hz, 50 msec minimum
width
Devices supported: Any device with isolated open drain, open collector, transistor or
reed switch
Supported on inputs: Standard inputs A-D, Optional inputs 1-6
Types: Contacting Flowmeter, Feed Verification, Generic Counter
High Speed Counter-Type
Digial Inputs
Electrical: Non-isolated 5 VDC with 301K ohm pull-up, 0-400 Hz, 1.25 msec
minimum width
Devices supported: Any device with isolated open drain, open collector, transistor or
reed switch
Supported on inputs: Standard inputs A-D, Optional inputs 5-6
Types: Paddlewheel Flowmeter, Generic Counter
Analog Inputs (1-8)
(Optional)
4-20 mA, 2-wire or 3 -wire, internally powered by 24 VDC, 25 ohm input resistance,
1000 ohm maximum load. Typical response time <10 seconds
Sensor STANDARD (1)
Sensor OPTIONAL (3)
Signal (isolated)
±1.5V
Signal (isolated)
±1.5V
Temp (isolated)
1K or 10K or 100K ohm
Temp (isolated)
1K or 10K or 100K ohm
Outputs
STANDARD
Mechanical relays:
At 115 VAC, 10 amp (resistive), 1/8 HP
At 230 VAC, 6 amp (resistive), 1/8 HP
R1, R2, R3, and R4 relays are fused together as one group, total current for this group must not exceed 5.5A
R5, R6, R7 and R8 relays are fused together as one group, total current for this group must not exceed 5.5A.
Relays 1-8 may be dry contact or may switch line (mains) voltage, depending upon model code; refer to Figure 4. Powered
relays have both NO and NC terminals available. Only powered relays are fused.
Digital: USB
Ethernet, 10 Base T
OPTIONAL
4-20 mA (1-4):
Isolated, 500 ohm max. resistive load, internally powered
Agency Approvals
Safety
UL 61010-1:2012 3rd Ed.
CSA C22.2 No. 61010-1:2012 3rd Ed.
IEC 61010-1:2010 3rd Ed.
EN 61010-1:2010 3rd Ed.
EMC
IEC 61326-1:2005
EN 61326-1:2006
Note: For EN61000-4-6, and EN 61000-4-3, the controller meets performance criteria B.
*Class A equipment: Equipment suitable for use in establishments other than domestic, and those directly connected
to a low voltage (100-240 VAC) power supply network which supplies buildings used for domestic purposes.
- Water Treatment Controller 1
- Instruction Manual 1
- TABLE OF CONTENTS 3
- 1.0 INTRODUCTION 5
- 2.0 SPECIFICATIONS 5
- Digital: USB 6
- Ethernet, 10 Base T 6
- Data Logging Menu 13
- 1/8 inch dia 16
- 3/16 inch dia 16
- 1/4 inch dia 16
- 5/16 inch dia 16
- 1/2" 150 PSI 17
- 1/2" 300 PSI 17
- 3/4" 150 PSI 17
- 3/4" 300 PSI 17
- 3.4 Icon Definitions 18
- Intermittent Sampling 20
- Continuous Sampling 21
- Hardwired Options 23
- Prewired Option 23
- IN+ +v IN- IN+ IN+IN-+v +v 24
- IN-IN-IN 24
- IN+IN+IN+ 24
- AC POWER 25
- sensors 2-4 26
- - PLC + 29
- GND +24 29
- 4.0 FUNCTION OVERVIEW 31
- Hard coded Fixed 34
- IP Address: 34
- 199.199.199.2 34
- Web Browser 34
- (Client) 34
- Embedded 35
- Web Server 35
- Fixed IP 38
- Address User 38
- Assigned 38
- 4.7 Startup 40
- 4.8 Shut Down 40
- 5.1 Input Summary 40
- 5.2 Indices 41
- 5.3 Output Summary 41
- 5.4 Alarms 41
- 5.5 Calibration 41
- Temperature Calibration 43
- ORP Calibration 44
- Calibrate 4 mA 46
- 5.6 Relay Control (HOA) 48
- 5.7 Set Points 48
- Relay 1- 8 Set Points 49
- 5.8 Communication 52
- 5.9 Access Codes 54
- 5.10 Software Upgrade 54
- 5.11 Copy to USB Disk 54
- 6.0 OPERATION – Using PC 55
- Controller Date Format 57
- Sensors 1-4 57
- Digital Inputs 57
- Relay (1 – 8) Control Mode 58
- 4-20 mA Inputs 1 - 8 58
- LCD Display Setup 61
- 6.3 System Summary Menu 61
- . The averaged reading 64
- Primary Sensor Assignment 66
- Current Reading/Calibrate 70
- . The averaged reading is 77
- Relay Control Mode 96
- Relay Input Assignment 96
- Current Reading 96
- Output Mode 118
- Hand Time Limit 118
- Event Log 118
- Power-up Alarm Delay Time 122
- Mutual Interlocks 122
- Output Time Limit 122
- Select items to log 142
- Suppresses Datalogging 142
- Triggers Datalogging 142
- Log Files 142
- Scenario 1: 143
- Scenario 2: 143
- Scenario 3: 143
- Ethernet (LAN) 145
- Email To Addresses 145
- ASMTP Settings 146
- Communications Status 146
- Activations 148
- 6.47 Advanced Comms 149
- Network Settings 149
- Import UCF 151
- 6.49 Notepad 151
- 6.50 Access Codes 151
- 6.52 Sub-Network 152
- 7.0 MAINTENANCE 153
- 7.6 Replacing the Fuses 157
- 8.0 TROUBLESHOOTING 158
- ORP Calibration Failure 159
- Output Time Out 161
- Conductivity High Alarm 162
- Conductivity Low Alarm 162
- ORP High Alarm 165
- ORP Low Alarm 166
- 4-20 mA Input Low Alarm 169
- Conductivity Sensor Error 169
- ORP Sensor Error 170
- Temperature Sensor Error 171
- Total Alarm Limit 171
- 8.3 CONNECTION PROBLEMS 177
- 9.0 SERVICE POLICY 178
Relacionado con productos y manuales para Redes Walchem WebMaster
Redes Walchem WebMaster Manual de usuario
(6 paginas)
(6 paginas)
Redes Walchem WebAlert Manual de usuario
(6 paginas)
(6 paginas)
Redes Walchem WebAlert Manual de instrucciones
(52 paginas)
(52 paginas)
Redes Walchem WebMaster Manual de instrucciones
(129 paginas)
(129 paginas)
Redes Walchem WebMaster Manual de instrucciones
(67 paginas)
(67 paginas)
Redes Walchem WebAlert Manual de usuario
(6 paginas)
(6 paginas)
Redes Walchem WebMaster Manual de usuario
(6 paginas)
(6 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales