Walchem WebMaster Manual de instrucciones Pagina 173
- Pagina / 180
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
169
Sensor Board Failure
This error message is caused by a failure of the controller to recognize that the option circuit board
is connected. The ORP output relay will be forced off.
Possible Causes Corrective Actions
Poor connection of the option board to Remove the option board and inspect both
the sensor interface board. mating connectors for corrosion or damage.
Reinstall the option board.
Faulty sensor input board. Replace the sensor input board.
4-20 mA Input Board Failure
This error message is caused by a failure of the controller to recognize that the option circuit board
is connected. If using a 4-20 mA type water meter, then bleed/feed output will be forced off.
Possible Causes Corrective Actions
Poor connection of the option board to Remove the option board and inspect both
the relay interface board. mating connectors for corrosion or damage.
Reinstall the option board.
Faulty 4-20 mA input board. Replace the board.
Digital Input Board Failure
This error message is caused by a failure of the controller to recognize that the option circuit board
is connected. If utilizing the Interlock feature, then any outputs that are set to deactivate in case of
an Interlock condition will be forced off.
Possible Causes Corrective Actions
Poor connection of the option board to Remove the option board and inspect both the
relay interface board. mating connectors for corrosion or damage.
Reinstall the option board.
Faulty digital input board. Replace the board.
Modem Failure
This error message is caused by a failure of the controller to recognize that the option circuit board
is connected.
Possible Causes Corrective Actions
Poor connection of the option board to Remove the option board and inspect both
the core board. mating connectors for corrosion or damage.
Reinstall the option board.
Faulty modem board. Replace the board.
- Water Treatment Controller 1
- Instruction Manual 1
- TABLE OF CONTENTS 3
- 1.0 INTRODUCTION 5
- 2.0 SPECIFICATIONS 5
- Digital: USB 6
- Ethernet, 10 Base T 6
- Data Logging Menu 13
- 1/8 inch dia 16
- 3/16 inch dia 16
- 1/4 inch dia 16
- 5/16 inch dia 16
- 1/2" 150 PSI 17
- 1/2" 300 PSI 17
- 3/4" 150 PSI 17
- 3/4" 300 PSI 17
- 3.4 Icon Definitions 18
- Intermittent Sampling 20
- Continuous Sampling 21
- Hardwired Options 23
- Prewired Option 23
- IN+ +v IN- IN+ IN+IN-+v +v 24
- IN-IN-IN 24
- IN+IN+IN+ 24
- AC POWER 25
- sensors 2-4 26
- - PLC + 29
- GND +24 29
- 4.0 FUNCTION OVERVIEW 31
- Hard coded Fixed 34
- IP Address: 34
- 199.199.199.2 34
- Web Browser 34
- (Client) 34
- Embedded 35
- Web Server 35
- Fixed IP 38
- Address User 38
- Assigned 38
- 4.7 Startup 40
- 4.8 Shut Down 40
- 5.1 Input Summary 40
- 5.2 Indices 41
- 5.3 Output Summary 41
- 5.4 Alarms 41
- 5.5 Calibration 41
- Temperature Calibration 43
- ORP Calibration 44
- Calibrate 4 mA 46
- 5.6 Relay Control (HOA) 48
- 5.7 Set Points 48
- Relay 1- 8 Set Points 49
- 5.8 Communication 52
- 5.9 Access Codes 54
- 5.10 Software Upgrade 54
- 5.11 Copy to USB Disk 54
- 6.0 OPERATION – Using PC 55
- Controller Date Format 57
- Sensors 1-4 57
- Digital Inputs 57
- Relay (1 – 8) Control Mode 58
- 4-20 mA Inputs 1 - 8 58
- LCD Display Setup 61
- 6.3 System Summary Menu 61
- . The averaged reading 64
- Primary Sensor Assignment 66
- Current Reading/Calibrate 70
- . The averaged reading is 77
- Relay Control Mode 96
- Relay Input Assignment 96
- Current Reading 96
- Output Mode 118
- Hand Time Limit 118
- Event Log 118
- Power-up Alarm Delay Time 122
- Mutual Interlocks 122
- Output Time Limit 122
- Select items to log 142
- Suppresses Datalogging 142
- Triggers Datalogging 142
- Log Files 142
- Scenario 1: 143
- Scenario 2: 143
- Scenario 3: 143
- Ethernet (LAN) 145
- Email To Addresses 145
- ASMTP Settings 146
- Communications Status 146
- Activations 148
- 6.47 Advanced Comms 149
- Network Settings 149
- Import UCF 151
- 6.49 Notepad 151
- 6.50 Access Codes 151
- 6.52 Sub-Network 152
- 7.0 MAINTENANCE 153
- 7.6 Replacing the Fuses 157
- 8.0 TROUBLESHOOTING 158
- ORP Calibration Failure 159
- Output Time Out 161
- Conductivity High Alarm 162
- Conductivity Low Alarm 162
- ORP High Alarm 165
- ORP Low Alarm 166
- 4-20 mA Input Low Alarm 169
- Conductivity Sensor Error 169
- ORP Sensor Error 170
- Temperature Sensor Error 171
- Total Alarm Limit 171
- 8.3 CONNECTION PROBLEMS 177
- 9.0 SERVICE POLICY 178
Relacionado con productos y manuales para Redes Walchem WebMaster
Redes Walchem WebMaster Manual de usuario
(6 paginas)
(6 paginas)
Redes Walchem WebAlert Manual de usuario
(6 paginas)
(6 paginas)
Redes Walchem WebAlert Manual de instrucciones
(52 paginas)
(52 paginas)
Redes Walchem WebMaster Manual de instrucciones
(129 paginas)
(129 paginas)
Redes Walchem WebMaster Manual de instrucciones
(67 paginas)
(67 paginas)
Redes Walchem WebAlert Manual de usuario
(6 paginas)
(6 paginas)
Redes Walchem WebMaster Manual de usuario
(6 paginas)
(6 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales