Walchem WebMaster Manual de instrucciones Pagina 102
- Pagina / 180
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
98
Accumulated Volume
This displays the volume of flow that has accumulated so far towards triggering the next feed
event. This is not the total flow, as seen in the System Summary page. This total will reset itself
once the feed has occurred. You can manually reset this total using the “Reset Total” button to the
right.
Custom Name
This menu allows you to call the output another name if desired. Type the new name in the text
box.
Unit Volume to Trigger Output
Type in the text box the volume of solution that needs to enter the system in order to trigger the
feed.
Output On-Time Per Unit Volume
Type in the text box the amount of time for the relay output to activate, once the previously
specified volume of solution has entered the system. Any value between 1 and 1440 minutes is
acceptable.
Reset Timeout (only appears if the Output Time Limit below has been exceeded)
There is a button called “Reset Timeout” which is used to reset the output if it has been activated
for longer than the time limit imposed in the “Output Time Limit” menu described below.
Mutual Interlocks
Click the check boxes to select or de-select the relays and analog output control outputs that you
want to be prevented from turning ON if this output relay is already ON. If you do not need any
other output to shut off when this relay turns on, UNCHECK all boxes. The selection is mutually
exclusive, meaning that if Relay 2 has Relay 4 interlocked, then R2 won’t turn on if R4 is already
on, and R4 won’t turn on if R2 is already on. This feature should be used with caution since it can
potentially delay a chemical addition for a long time.
Output Time Limit
Type in the text box the maximum amount of time that the relay can be continuously activated
before the controller deactivates the relay and activates an Output Time Limit alarm. This is
intended to prevent the output from running out of control if the input fails in such a way that it
will never deactivate the relay.
Note that the relay will not activate again until someone resets the timer!
It will take some experience to find out what the normal output on-time will be. If the relay cycles
open and closed under worst case conditions in 30 minutes, you may want to set the Output Time
Limit at 60 minutes.
Hand Time Limit
Type in the text box the maximum number of minutes that the relay can be activated in the Hand
mode. Any value between 1 and 1440 is acceptable.
Click on the “Submit” button to save the changes.
- Water Treatment Controller 1
- Instruction Manual 1
- TABLE OF CONTENTS 3
- 1.0 INTRODUCTION 5
- 2.0 SPECIFICATIONS 5
- Digital: USB 6
- Ethernet, 10 Base T 6
- Data Logging Menu 13
- 1/8 inch dia 16
- 3/16 inch dia 16
- 1/4 inch dia 16
- 5/16 inch dia 16
- 1/2" 150 PSI 17
- 1/2" 300 PSI 17
- 3/4" 150 PSI 17
- 3/4" 300 PSI 17
- 3.4 Icon Definitions 18
- Intermittent Sampling 20
- Continuous Sampling 21
- Hardwired Options 23
- Prewired Option 23
- IN+ +v IN- IN+ IN+IN-+v +v 24
- IN-IN-IN 24
- IN+IN+IN+ 24
- AC POWER 25
- sensors 2-4 26
- - PLC + 29
- GND +24 29
- 4.0 FUNCTION OVERVIEW 31
- Hard coded Fixed 34
- IP Address: 34
- 199.199.199.2 34
- Web Browser 34
- (Client) 34
- Embedded 35
- Web Server 35
- Fixed IP 38
- Address User 38
- Assigned 38
- 4.7 Startup 40
- 4.8 Shut Down 40
- 5.1 Input Summary 40
- 5.2 Indices 41
- 5.3 Output Summary 41
- 5.4 Alarms 41
- 5.5 Calibration 41
- Temperature Calibration 43
- ORP Calibration 44
- Calibrate 4 mA 46
- 5.6 Relay Control (HOA) 48
- 5.7 Set Points 48
- Relay 1- 8 Set Points 49
- 5.8 Communication 52
- 5.9 Access Codes 54
- 5.10 Software Upgrade 54
- 5.11 Copy to USB Disk 54
- 6.0 OPERATION – Using PC 55
- Controller Date Format 57
- Sensors 1-4 57
- Digital Inputs 57
- Relay (1 – 8) Control Mode 58
- 4-20 mA Inputs 1 - 8 58
- LCD Display Setup 61
- 6.3 System Summary Menu 61
- . The averaged reading 64
- Primary Sensor Assignment 66
- Current Reading/Calibrate 70
- . The averaged reading is 77
- Relay Control Mode 96
- Relay Input Assignment 96
- Current Reading 96
- Output Mode 118
- Hand Time Limit 118
- Event Log 118
- Power-up Alarm Delay Time 122
- Mutual Interlocks 122
- Output Time Limit 122
- Select items to log 142
- Suppresses Datalogging 142
- Triggers Datalogging 142
- Log Files 142
- Scenario 1: 143
- Scenario 2: 143
- Scenario 3: 143
- Ethernet (LAN) 145
- Email To Addresses 145
- ASMTP Settings 146
- Communications Status 146
- Activations 148
- 6.47 Advanced Comms 149
- Network Settings 149
- Import UCF 151
- 6.49 Notepad 151
- 6.50 Access Codes 151
- 6.52 Sub-Network 152
- 7.0 MAINTENANCE 153
- 7.6 Replacing the Fuses 157
- 8.0 TROUBLESHOOTING 158
- ORP Calibration Failure 159
- Output Time Out 161
- Conductivity High Alarm 162
- Conductivity Low Alarm 162
- ORP High Alarm 165
- ORP Low Alarm 166
- 4-20 mA Input Low Alarm 169
- Conductivity Sensor Error 169
- ORP Sensor Error 170
- Temperature Sensor Error 171
- Total Alarm Limit 171
- 8.3 CONNECTION PROBLEMS 177
- 9.0 SERVICE POLICY 178
Relacionado con productos y manuales para Redes Walchem WebMaster
Redes Walchem WebMaster Manual de usuario
(6 paginas)
(6 paginas)
Redes Walchem WebAlert Manual de usuario
(6 paginas)
(6 paginas)
Redes Walchem WebAlert Manual de instrucciones
(52 paginas)
(52 paginas)
Redes Walchem WebMaster Manual de instrucciones
(129 paginas)
(129 paginas)
Redes Walchem WebMaster Manual de instrucciones
(67 paginas)
(67 paginas)
Redes Walchem WebAlert Manual de usuario
(6 paginas)
(6 paginas)
Redes Walchem WebMaster Manual de usuario
(6 paginas)
(6 paginas)
Indesit BAN 14 manuels
Manuels d'utilisation et guides de l'utilisateur pour Réfrigérateurs-congélateurs Indesit BAN 14.
Nous fournissons des manuels en pdf 1 Indesit BAN 14 à télécharger gratuitement par type de document : Mode d'emploi
Comentarios a estos manuales